基准平面垂直断面法在爆破漏斗试验中的应用

系统阐述了基准平面垂直断面法在爆破漏斗试验中测量爆破漏斗体积的基本原理,并将隧道激光断面仪应用于金厂河矿1 750 m水平15^#采场底部切割巷道爆破漏斗试验爆破漏斗体积测量中。通过与传统体重法等计算法所得漏斗体积分析比较,结果表明基于隧道激光断面仪与3D Mine软件分析的基准平面垂直断面法实用性强、操作方便、结果直观可靠,达到试验预期目的。     

基于BIM超高层密集布筋区埋入式型钢混凝土柱脚施工技术

以漳州市某超高层项目为例,针对超高层密集布筋区埋入式型钢柱脚与钢筋的深化设计、地脚螺栓的定位预埋、型钢柱脚支撑体系设计、节点钢筋穿插连接施工、埋入式型钢柱脚安装等方面,提出切实可行的施工方法,解决了埋入式型钢混凝土柱脚的地脚螺栓精准预埋、与底板密集钢筋穿插连接施工、悬空支撑稳定等一系列施工技术难题,既满足了设计方案的要求,又可为类似工程提供借鉴。     

Experimental study on free and submerged multi-jets

The flow characteristics of the hydraulic jump due to parallel jets are different from the classical jump emerging from a single gate. Due to the highly complex flow field at the downstream pool, deciding about the tailwater measuring location is a challenging issue affecting the flow measuring accuracy. Experiments are conducted herein, on different parallel jets’ configurations for both free and submerged flow conditions. To quantify the flow uniformity, for any downstream cross section, the associated momentum correction factors, β₂, were estimated for the free-flow condition. It is found that β₂-values depend significantly on the measuring location, and consequently the available conjugated depths relationship results in poor estimation when measuring location moves downstream. Employing Buckingham analysis, a general formula is proposed to calculate the momentum correction factors associated with the free hydraulic jump at different downstream measuring locations. The experimental results of this study indicated that such a formula enhances distinguishing between free and submerged flow conditions of the gates installed in parallel. Finally, a dimensionless stage-discharge formula is presented to predict the submerged flow rate through parallel gates of different gate openings and widths.     

Benchmark experiment of large-angle scattering reaction cross section of iron at 14 MeV using two shadow bars – Comparison of experimental results with ENDF/B-VIII –

ABSTRACT

It is important to perform neutron transport simulations with accurate nuclear data in the neutronics design of a fusion reactor. However, absolute values of large-angle scattering cross sections vary among nuclear data libraries even for well-examined nuclide of iron. Benchmark experiments focusing on large-angle scattering cross sections were thus performed to confirm the correctness of nuclear data libraries. The series benchmark experiments were performed at a DT neutron source facility, OKTAVIAN of Osaka University, Japan, by the unique experimental system established by the authors’ group, which can extract only the contribution of large-angle scattering reactions. This system consists of two shadow bars, target plate (iron), and neutron detector (niobium). Two types of shadow bars were used and four irradiations were conducted for one experiment, so that contribution of room-return neutrons was effectively removed and only large-angle scattering neutrons were extracted from the measured four Nb reaction rates. The obtained experimental results were compared with calculations for five nuclear data libraries including JENDL-4.0, JEFF.-3.3, FENDL-3.1, ENDF/B- VII, and recently released ENDF/B-VIII. It was found from the comparison that ENDF/B-VIII showed the best result, though ENDF/B-VII showed overestimation and others are in large underestimation at 14 MeV.     

圆形截面柱的振动台试验及分析

进行了圆柱振动台试验,对模型的加速度反应数据进行获取。试验表明,随着地震的加速度峰值的不断增加,圆柱顶部加速度极值不断增加。柱顶的加速度响应有着增大的趋势,且极值比输入的加速度的极值有一定的放大。     

高低孔爆破处理高陡边坡的技术分析

针对前期规划不当,大宝山露天矿877 m平台高陡边坡局部存在难以采用预裂爆破技术进行处理的情况,决定采用高低孔爆破处理技术。为了解决这一难题,首先分析了高低孔的相对内涵,并对高低孔孔深计算公式进行了简单推导,然后通过公式计算得到了高低孔的孔深。在施工阶段,为了确保低孔的实施效果,两排低孔分区域使用同段别毫秒延时雷管,晚于高孔起爆。实践表明,处理后的平台平整度良好,坡面较为稳定,对高陡边坡采用高低孔爆破处理具有可行性,效果较好,可为类似边坡处理提供新思路。     

AP1000稳压器波动管竖直管段空气-水CCFL实验研究

使用竖直管代替波动管模型开展稳压器波动管竖直管段内空气-水两相逆流限制（CCFL）特性可视化实验研究。实验现象表明:竖直管与上容器接口处的局部CCFL决定了进入竖直管内的液相流量；竖直管内的局部CCFL决定了从竖直管流出的液相流量；两处局部CCFL均随空气流量的增大而增强。在较低气量情况，进入竖直管内的液相能够完全或大部分流出，竖直管内的局部CCFL较弱，上容器和竖直管接口处的局部CCFL在整体CCFL中占主导地位，整体CCFL程度随着上容器液位升高而略有增强。在高气量情况，从上容器进入竖直管的液相大部分或者完全被限制而不能向下流出，竖直管内的局部CCFL强烈，在整体CCFL中占主导地位，整体CCFL特性不受上容器液位变化的影响。通过实验数据拟合得到了新的稳压器竖直管CCFL模型。稳压器波动管CCFL数据和稳压器竖直管CCFL数据基本重合，表明波动管CCFL主要由CCFL-U决定。      

带扩张段构型超声速气流中横向射流数值模拟

针对带扩张段构型的发动机燃烧室,采用欧拉-拉格朗日仿真方法研究喷注方式、喷孔参数及隔离段燃烧室构型的改变对于射流雾化效果的影响,用以更好地指导发动机设计.结果表明,在保证发动机总体流量不变的条件下,喷孔孔径减小或者喷孔总数量减少使得液气动量通量比增大,有利于同时增大单孔射流穿透深度以及液滴展向宽度.贫燃工况下如当量比为0.7条件下,射流流量减小,混合效果可能变差.而在发动机结构设计方面,隔离段到燃烧室的过渡设计不宜采用大转角,15°转角是相对较为理想的设计方案.采用小角度突扩构型设计比渐扩构型更容易找到相对好的点火位置.     

Optical in-process height measurement system for process control of laser metal-wire deposition

We propose an in-process height measurement system for a weld bead and feedback control system for wire-feeding speed for high-quality laser deposition. Metal additive manufacturing, especially laser metal-wire deposition, is effective for complex shape fabrication and repair processing. However, we must control the gap between a weld bead and a feed wire in an optimal range for high-quality deposition. Conventionally, the Z-stage pitch for multi-layer deposition must be precisely adjusted by each deposition shape. In this paper, we design an in-process height measurement system that is integrated in a laser processing head, which measures the weld bead height by a line section method. We decreased the influence of the intense thermal radiation generated from a melt pool by inserting the band-pass filter of the line beam's wavelength in the imaging system and optimizing its line laser power. Consequently, our system can measure the weld bead height near the melt pool, which is 4 mm in front of it. Next we show that our proposed system can measure the weld bead height during wire-laser metal deposition with 50-μm accuracy by comparing its value to the true value. Finally, we achieved a cylinder shape deposition of 50-mm height, regardless of the Z-stage pitch and the cylinder diameter of the multi-layer deposition, by controlling the wire-feeding speed based on the measured weld bead height.